Other

HOTweezers  represent the state of the art in the design and construction of thermal wire strippers.

Hotweezers thermal wire strippers weigh less than 57g including cable and connector, making it an ideal hand-held solution with smooth and efficient operation. The heater filaments are completely sealed in the stripping head of a Hotweezers thermal wire stripper device enhancing its performance consistently.

Advantages of using HOTweezers:

1. The filament is resistant to oxidation.

2. The stripping head will not distort nor lose alignment as is the case with ordinary hot wire strippers.

3. Since the filaments are enclosed, a greater portion of the heat generated is retained to do useful work. Consequently the power supply can be much smaller than usual, and the current consumption is drastically reduced. The M-10 power supply consumes a mere 20 watts at the highest temperature setting.

4. Wire holes can be ground into the stripping head without damage to the filaments. With wire holes, the rotation of the stripper required to accomplish a strip is reduced from 180o to 15o and mashing of conductors, especially the finer gauges, is completely eliminated.

5. Because the filaments are an integral part of the stripper body, no maintenance is required.

Three different models of the HOTweezers are available to satisfy most stripping requirements. For precise insulation removal Models 4A and 4B have stripping holes to yield a clean, even strip free of insulation "tails" and to prevent mashing of the conductor strands. Model 4C is designed for use on cable jackets and larger diameter conductors. Maximum cable or conductor O.D. that can be stripped is 0.25 inch (6.35 mm) and maximum insulation wall thickness is .05 inch (1.27 mm). For stripping requirements that exceed these dimensions the HOTnife can be used. All models have the new strip length gauge so that repetitive stripping operations can be done accurately. The gauge is easy to adjust without a screwdriver or special tools. The standard power cord for all three models is a flexible, lightweight cable with a high temperature silicone rubber jacket that resists burns.

If you have a requirement that may require a special model, please contact us directly.

Image shows tweezer with power supply.

Go Geothermal Ltd, the UK’s Largest independent supplier of Air Source and Ground Source Heat Pumps.  Supplying premium brands such as Vaillant, Stiebel Eltron, Mitsubishi along with the very best Underfloor Heating Products, Solar Aerovoltaic, Solar Thermal, Preinsulated Pipe, Cylinders, Probes, Ground Loops, Chamber Manifolds, Glycol etc etc., we are the One Stop Shop for all things Renewable.  Over 97% of the products we sell are stocked and available for delivery next day to most of the UK.

You can view our product brochure here: https://www.gogeothermal.co.uk/wp-content/uploads/GoGeothermal-Product-Brochure.pdf

We provide top quality commercial dishwashers from Cater-Wash, Electrolux Professional, Hobart, Hobart Bar Aid & Hobart Ecomax.

Since 1970, our machines have been built using only the most reliable mechanical components available, with no need for printed circuit boards. Manufactured from high grade AISI 304 and featuring double skinned doors to lower the noise and retain heat. All commercial dishwashers are fitted with a breaktank which provides a fully KIWA approved air gap.

Additionally, primary and secondary filtration systems mean longer lasting water quality and improved performance.

At Link Instruments, we are a global supplier of quality products such as CO2 level indicators to the marine, fire safety, diving and electrical industries.

Our ULLC2001 ultrasonic liquid level indicator is used accurately around the globe as a reliable halo, FM200 and CO2 level indicator in liquid gas cylinders.

AML Instruments are a family run business offering instrumentation, UKAS ISO 17025 calibration, service, repair, spare parts and support for a wide range of instruments / test equipment used in a variety of industries and applications.

At Tennco Distribution Limited, we are a progressive electromechanical component distributor. We are family owned and operate in niche markets concentrating on electronic and electrical components for the computing, networking, instrumentation, panel building, audio and circuit board assembly industries.

Backed by 30 years experience, at Tennco, we are committed to service and efficient components distribution coupled with ISO 9002 approval. We offer products at competitive prices with a fast friendly and efficient service.

At Paramount Electronics we specialise in industrial electronic repairs, exchange circuit boards and the design and manufacture of industrial electronics. Our highly skilled engineers have the knowledge and experience to undertake almost any form of industrial electronic repair, and all repairs are completed at a fixed price with a 2 year guarantee.

We have been developing and manufacturing a wide range of measurement instruments since 1920, always with an emphasis on quality, durability and service. As our products remain in use throughout the world we continue to support our customers with spares, repairs and replacements and reengineered products.
In 2001 we joined with Rheintacho GmbH to create one of the largest rotational speed measurement manufacturers in the world. Rheintacho brings over 100 years of additional expertise, especially in the field of non-contact rotational speed sensors and stroboscopes.
As a consequence, our expanded range now covers a wide selection of products for the measurement, indication and control of rotational speed together with a range of stroboscopes for quality control and maintenance. 
Our handheld portable range of tachometers and stroboscopes provides the user with the ability to measure speed and distance as well as carrying out maintenance checks by creating a ‘frozen’ image using a strobe. With equipment for use in a range of environments and applications there is a solution for every need. 
Where a fixed solution is required we offer stroboscopes with a range of light sources, widths and trigger configurations to suit individual demands.
Our rotational speed instruments range from mechanical indicators which are directly connected to moving components, to non-contact sensors which generate a signal from the component and transmit this to electronic devices for control and indication. With this range we have the capability to supply effective solutions from stock, or to engineer existing products to meet specific requirements, either as a ‘one-off’ or for a serial production.
Our technical strength is key to remaining at the forefront of our industry, and we work closely with our clients during the product development process to ensure that when we design and develop a product for them it meets the specification and adds value to the finished product. Quality, accuracy and durability are fundamental to our success.
We believe that we can provide a cost-effective solution for your needs, and if there is not currently a standard product, please talk to us and see what we can do for you.

Howard Butler Ltd has been manufacturing panel meters, current transformers, relays, transducers and associated products in our UK factory for over 85 years.

Howard Butler Ltd has ISO 9001:2008 approval with a constantly reviewed quality policy. This ensures that through our  vigilance, control, design methods and accountability throughout all stages of design and manufacture quality is designed and built into our products. Our in-house design engineers are able to work with customers to provide custom solutions where our standard product range is not applicable. Our policy is one of continuous improvement, therefore the HOBUT range is regularly added to with new products, mostly designed to IEC, BS, or DIN specifications.

We hold extensive stocks of vital components to ensure quick delivery of both standard and special
products. Customer satisfaction is central to the aims of Howard Butler Ltd, with our fully integrated
computer system closely controlling orders, enquiries and stock.

We are the exclusive sales and service centre for Swagelok in Scotland, North East England and Ireland. We have been providing an extensive range of fluid system products and services for over 30 years and are recognised as experts in our field.

Whether a multinational corporation or a local plant operation, our customers benefit from the expertise and resources of working with a global organisation. Swagelok Scotland, Teesside and Ireland provide products, solutions and services that are most helpful and relevant to our customers’ challenges.

To support our inventory of fluid system components, Swagelok Scotland, Teesside and Ireland offers a growing range of services including training, eBusiness and integrated services such as inventory management solutions and assembly services, onsite inspection services, equipment and tool hire and supply chain optimisation. With an extensive inventory of products for immediate delivery, this allows Swagelok to provide high quality products and an exceptional service to our customers.

Contact Swagelok Scotland, Teesside and Ireland for further information about our range of products including: - Fittings - Valves - Hoses and Flexible Tubing - Regulators - Quick Connects - Measurement Devices - Tubing and Tube Accessories - Filters - Sample Cylinders - Miniature Modular Systems - Pre-Engineering Subsystems - Welding Systems - Leak Detectors, Lubricants and Sealants.

scotland.swagelok.com

PLAST-CONTROL was formed in 1979 and launched its first product the Gravimetric Extrusion control system later that year. Since then we have grown with continuous development of products and new product launches approx. every two years.

Our innovative and class leading system and sensor hardware technologies are used extensively in the blown film extrusion and continuous sheet and profile extrusion industries worldwide.

Were always striving to deliver market relevant products which reduce operational costs and raw material consumption and have excellent service and low operational costs.

PLAST-CONTROL UK has represented PLAST-CONTROL GmbH in the UK since 1990 and provides technical consultation services, UK based installation, commissioning, service and after sales support as well as holding comprehensive stocks of spares parts and consumables for the complete product range.

Penico Gauges management & production staff has been involved with the Glass Container Industry for over 30 years. In this time we have had the privilege to work with many talented people in mould repair & mould manufacturing workshops. We have developed a deep understanding of the problems facing the mouldmaker & repairer. Penico can offer a solution to your Gauging needs. Bring to us your gauging problems & we will work with you to help you solve your difficulties.

Penico Gauges has exported to over 40 countries. We look forward to being able to serve you.

Please contact on info@penico.com with any enquiries.

Penico Gauge Limited is Known worldwide as a well-established and respected Gauge Manufacturing and precision engineering company Based in Bingley. We specialise in Gauges and sub-contract bespoke machining and offer an unrivalled combination of:
 

• High precision

• Quality

• Reliability

• Flexibility

All our staff have over 30 years’ experience in the manufacture of precision gauges, jigs, fixtures, general-purpose and precision machining to our customers’ requirements.

We Have the Skills and knowledge for all types of industries, from Glass and food industry, press tooling, plastic injection to aerospace and worked with a wide range of materials.

We have the facilities to carry out:

• • Cad Design
  • Universal grinding
  • Surface grinding
  • CNC Grinding
  • Wire eroding
  • Spark eroding
  • Conventional milling And Turning
  • CNC milling
  • CNC Turning
  • Laser Engraving (Fibre and Co2)

Tritex NDT manufacture and supply a range of multiple echo ultrasonic thickness gauges used to determine corrosion levels and measure metal thickness without disturbing or affecting protective coatings, only the metal thickness is measured. All gauges have Intelligent Probe Recognition (IPR) as well as Automatic Measurement Verification (AMVS).

Our ultrasonic thickness gauges are used all over the world in all applications where metal thickness and corrosion is of concern. They have been designed to be robust for use in extremely harsh conditions and all gauges are built to the highest standards. We are an ISO9001 certified company and committed to quality and customer service from first contact and throughout the active life of the gauge.

 Fully equipped temperature controlled calibration laboratory offering a wide range of services on mechanical and digital measuring instruments and gauges. The laboratory is long established having gained UKAS Accreditation in 1990.
 SLIP GAUGES, TORQUE WRENCHES, SCREW THREAD GAUGES, MICROMETERS etc.