Antech Calibration Services

0 PRODUCTS/SERVICES
- EMPLOYEES
- YEAR FOUNDED

Antech Calibration Services, established in February 1988, has built a reputation for quality service and versatility with our customers, allowing it to become one of the premier instrument calibration and engineering laboratories in the UK serving the agrochemical, food, manufacturing, oil/gas, petrochemical, pharmaceutical and utility sectors.

Customers

Located in GREAT YARMOUTH Norfolk, Antech's principal aim is the continued development of our UK customer base, however it's location makes it ideally placed to meet the demands of our new customers in Europe while continuing to service the growing needs of our UK customers.

UKAS Calibration

Antech can offer UKAS Calibration over many fields including:

Traceability

Calibrations for direct traceability with National Standards using Antech's UKAS Calibration Laboratory encompassing BS EN ISO/IEC 17025 and standard calibrations to individual company's internal requirements. Both meet the requirements of BS EN ISO 9001:2008

Electrical

Antech's UKAS electrical calibration laboratory caters for all types of general purpose electrical instruments across a wide range of industries.

The wide range of equipment covered falls into the following categories: -  
  • Analogue/Digital Multi-meters, Oscilloscopes, Resistors
  • Clip-on Ammeters, Power Supplies, Stop Watches
  • Frequency Timer/Counters, Potentiometers, Tachometers
  • Insulation Testers, Resistance Boxes, Temperature Indicators
  • Low Resistance Meters, Voltage References, Shunts
  • Oscillators and Signal Generators
All with certification, and within the following parameters:-
Electrical Parameters
 
  • DC Voltage 0 to 60 kV
  • DC Current 0 to 2000 Amps, 0 to 100 Amps source simulated above 100 Amps, 2 to 2000 Amps Simulated.
  • AC Voltage 0 to 1100 V @ 10 Hz to 1 MHz. 0 to 50 kV peak @ 50 Hz
  • AC Current 0 to 2000 Amps, 0 to 100 Amps source simulated above 100 Amps, 2 to 2000 Amps Simulated @ 40 to 60 Hz
  • Frequency Measurement & Generation DC to 1.2 GHz
  • Time 0.1s to 1 Hour, Hand Held Stopwatch
  • Phase angle 0.1° to 359.9°, -180.0° to + 180.0°
  • DC Resistance 0Ω to 100 GΩ
  • AC Resistance 1 mΩ to 10 kΩ
  • Capacitance Measured 1 pF to 100 mF & Generated 50 pF to 1 μF @ 100 Hz to 100 kHz
  • Inductance Measured 0.1 mH to 30 kHz & Generated 0.1 mH to 1 H @ 100 Hz to 100 kHz

Accelerometry Parameters
  • Frequency Step 10 Hz to 50 kHz
  • Amplitude 0.1 gn to 10 gn

Temperature

Following the completion of our new purpose built temperature and humidity laboratory housing chambers, dry blocks and liquid baths. Antech Calibration Services can continue to improve on its temperature capability and provide the very best temperature calibration service.

The range of products handled fall into the following categories: -
  • Resistance Thermometers (PRT)
  • Liquid-in-glass Thermometers
  • Thermocouples
  • Temperature Block Calibrators
  • Temperature Indicators and Recorders
  • Temperature Data Loggers
  • Infrared Radiation Thermometers
     
All with certification, within the following parameters: -
  • PRT -80°c to +660°c
  • (Electrical) -200°c to + 850°c
  • Thermocouples -80°c to +1100°c
  • (Electrical) -270°c to +1768°c
  • Liquid-in-glass Thermometers -80°c to +200°c
  • Temperature Block Calibrators -38°c to +1100°c
  • Infrared Radiation Thermometers -15°c to +500°c

Pressure

Over the last decade Antech Calibration Services has developed its UKAS pressure calibration laboratory capability to cover the vast range of instruments found in industry today: -

The wide range of pressure calibration equipment covered falls into the following categories: -  
  • Gas/Hydraulic-Absolute, Differential, Gauge, Negative Gauge
  • Fiscal Metering
  • Air/Oil Dead Weight Testers
  • Anemometers
  • Micromanometers
  • Orifice Plates to 30"
  • Barometers (Kew, Fortin & Aneroid)
  • Gas Density
All with certification, within the following parameters: -  
  • Hydraulic Pressure Gauge 0 to 4000 bar
  • Hydraulic Pressure Absolute 0 to 4000 bar
  • Gas Pressure Gauges -1 to 500 bar
  • Gas Pressure Absolute 0 to 500 bar
  • Gas Pressure Vacuum 0 to -1 bar
  • Differential Pressure 0 to 10 bar
  • Differential Pressure High Static 0 to 400 bar
  • Air velocity 0.5 m/s to 30 m/s
Our UKAS pressure calibration laboratory can also offer torque calibration in the range 0 to 1000 Nm and force calibration in the range 0 to 5000 kgf.
  Gas Density Transducers

Certification using Antech's UKAS Calibration Laboratory of gas density transducers in the range 0 to 400kg/m³ using nitrogen or argon gas. Additionally, for fiscal metering customers, we can produce a 'User gas' certificate for a gas of a known composition. You can supply your gas composition details by completing the online user gas composition form below:
High Static Differential Pressure

Certification using Antech's UKAS Calibration Laboratory of differential pressure transmitters with analogue or digital output. Maximum differential pressure: 10 bar, maximum line pressure: 400 bar. Atmospheric 'footprint' calibration is performed after high static calibration. Please fill in our differential pressure transmitter calibration online form below to ensure the rapid calibration of your instruments:

Humidity

Following the completion of our new purpose built temperature and humidity laboratory. Antech Calibration Services has included in its porfolio Humidity and Air Temperature capabilities, which is commensurate within the market place.

Humidity

The range of humidity products handled fall into the following categories: - 
  • Digital Indicators and Probes
  • Humidity Generators
  • Humidity Recorders
  • Tinytag Sensors
  • Thermohygrographs
  • Temperature Transmitters
  • Humidity Transmitters
  • Humidity Saturated Salts
  • Dewpoint Meters
All with certification within the following parameters: -
  • Measurement, Not Source atm 10% RH to 95% RH
Air Temperature

Certification within the following parameters: -
  • Temperature in air -25°c to 100°c

Liquid Flow

Antech is proud of it's calibration abilities with the award and continuing additions to it's UKAS Accreditation. Within the last year Antech has included liquid flow calibration capabilities to it's portfolio. Additional premises were necessary to house our liquid flow rigs and after an initial setup period Antech Calibration Services is now UKAS accredited.

The typical range of equipment covered falls into the following categories: -  
  • Coriolis Flowmeters
  • Turbine Flowmeters
  • Positive Displacement Flowmeters
  • Ultrasonic Flowmeters
  • Electromagnetic Flowmeters
We can now offer the following liquid flow calibration: -
  2500 L/min UKAS Accredited Hydrocarbon Rig
  • Oil viscosity 2 to 200 cSt
  • Mass Flow 20 to 2000 kg/min, uncertainty of 0.075%
  • Volumetric flow 25 to 2500 L/min, uncertainty of 0.1%
60 L/min UKAS Accredited Hydrocarbon Rig
  • Oil viscosity 2 to 200 cSt
  • Mass Flow 0.5 to 50 kg/min, uncertainty of 0.1%
  • Volumetric flow 0.6 to 60 L/min, uncertainty of 0.15%
The fluid temperature can be controlled from 25°c to 80°c, which enables the viscosity to be matched to your requirements.   600 L/min UKAS Accredited Water Rig
  • Mass flow 4 to 600 kg/min, uncertainty of 0.2%
  • Volumetric flow 4 to 600 L/min, uncertainty of 0.2%
2000 L/min UKAS Accredited Gas Flow Rig
  • 0.2 L/min to 2 L/min, uncertainty of 0.23%
  • 2 L/min to 2000 L/min, uncertainty of 0.16%
Calibration of equipment such as Variable Area, Positive Displacement and Thermal Mass Flowmeters etc....

Dimensional

Antech offer a calibration, repair and manufacturing service for orifice plates. Certification is to ISO5167-1:2003 and is issued by Antech's UKAS Calibration Laboratory. Our maximum plate size is 36" - there is no minimum size restriction. All measurements are recorded directly into a computer; a typical calibration contains a minimum of 160 individual measurements.

For calibration of orifice plates, pipeline diameter is required as this feature determines the tolerances of the orifice plate during the calibration process. The following form enables rapid delivery:

Antech can manufacture bespoke orifice plates in addition to offering calibration. Please contact us for price and delivery.

The link below provides a PDF document detailing a typical orifice plate drawing:

Universal Orifice Plate Drawing

Hire

For customers in today's advanced technological field, it is vital to have access to the very latest state-of-the-art equipment in the fields of measurement, process simulation and monitoring.

Hiring effectively can cut both maintenance and repair bills, especially for customers holding equipment that may only be used for brief and infrequent periods. Holding equipment like this is expensive in terms of purchase, servicing, annual certification and storage. The obvious answer, especially when equipment is needed urgently, is to rent.

Antech's highly trained sales engineers will assist in ensuring you are recommended the right product to hire for the job. Our comprehensive range of measurement, process simulation and monitoring equipment is supplied, serviced and with its calibration traceable to National Laboratory standards.
From simple mechanical chart recorders for pressure and temperature measurement, hydraulic pumps or flushing rigs, multimeters, oscilloscopes, temperature dry block calibrators, 'Dalek' gas detectors and dead-weight testers to 'Fiscal Metering' test equipment, all available from a single supplier.
If Antech does not stock what is required, our engineers can source it.
Test Equipment Sales:

Our engineers specify and procure instrumentation and valves for the client. Framework agreements with major manufacturing companies ensure we meet clients requirements. Our sales engineers will specify and source the right equipment and the customer can be confident that Antech will provide lifetime calibration and support.

Contact Us

" For Further Information CLICK HERE "

"Don't Forget To Say You Found Us On Applegate Directory"

Can we help?